2.5 Horsepower Boat Outboard Engine Air-cooling Gasoline Fuel Short Shaft Two 2 strok Outboard Motor For Inflatable Boat Item NO.: 3256802449304308

1. Applicable ship type
The two-stroke 2.5-horsepower upgraded outboard engine is suitable for small boats of various materials (such as inflatable boats, iron boats, plastic boats, fiberglass boats, wooden boats, etc.) from 2.0 meters to 2.5 meters.

2. Driving conditions
The built-in fuel tank is filled up once, and it runs at full throttle. Normally it can run for about 1.0 hour, and the driving speed is about 10Km/h (Due to different ship types, loads, and natural conditions, the driving speed will vary)

3. Fuel use
The fuel for two-stroke machines is mixed oil, that is, gasoline and two-stroke engine oil are mixed at 25:1. The gasoline is 92# and above unleaded pure gasoline. Need to add oil separately).

4. Other instructions
This machine has no reverse gear; the throttle is continuously variable; the air-cooled system; aluminum alloy three-blade propeller; the machine can be rotated 360 degrees as reverse gear, and the clamping device can adjust the height up and down.
 

PARAMETER

Power: two stroke 2.5 horsepower
Size: 108*32*30/13cm (package size)
Weight: 8.2kg (net weight)
Speed: 8500 rpm
Displacement: 52cc
Ignition system: CDI
Control system: steering handle
Start mode: pull start
Gear position: continuously variable (no reverse gear)
Tilt system: manual tilt
Fuel tank capacity: 1.2L
Carburetor: diaphragm type
Cooling system: air cooling
Fuel: 92# gasoline mixed with two-stroke engine oil 25:1
Recommended engine oil: two-stroke engine oil
Propeller: 3-blade aluminum (18cm diameter)
Shaft length: short shaft (applicable mast distance from the water surface ≤45cm)

DETAILS

Throttle
The damper is used when the cold engine is started. It is closed before starting, and it is not necessary after the engine is warmed up. The damper should be fully open, and the damper shall be fully open when in use.

Gear Oil
There is a screw on the gear box. You can add gear oil by unscrewing the screw. Each machine will be filled with gear oil before leaving the factory. You don't need to fill it for the first time.

Accelerator
L is low speed, H is high speed, the oil has idling speed, and the propeller will not rotate until the throttle is increased.

Tank
As express delivery does not allow liquid transportation, the fuel tank is emptied so that the machine does not leak oil during transportation, and fuel should be filled first when it is received.

COMMON PROBLEM

Q: What is the difference between two-stroke and four-stroke engines?

A: Two-stroke means that the engine piston moves up and down twice to complete a cycle; four-stroke means that the engine piston moves up and down four times for one cycle;
Two-stroke: strong explosive force, simple structure, simple maintenance, light weight, fast speed increase, slightly higher fuel consumption, slightly louder noise, high temperature; fuel is required to be mixed oil, that is, 92# gasoline and two-stroke engine oil are mixed 25:1;
Four-stroke: high efficiency, low emissions, fuel saving, low sound, high complexity, high cost; fuel is pure gasoline, engine oil is lubricating oil, and is filled separately.
Note: Two-stroke engine oil is fuel oil, and four-stroke engine oil is lubricating oil, and cannot be mixed.

Q: Do I need to add gasoline and oil after receiving the machine?

A: Because it is not possible to send packages containing liquids for transportation, each machine will be emptied of oil after commissioning. After receiving the machine, it can be used after installation. Injection of mixed oil, that is, 92# pure gasoline and two-stroke engine oil are mixed with 25:1)

Q: What issues should be paid attention to in storage and transportation?

A: Gasoline is easy to oxidize and deteriorate during storage. Using deteriorated gasoline will cause difficulty in starting and block the oil circuit. If you do not use the engine for more than half a month, please drain the fuel.
The four-stroke machine is used to check the oil for the first 5 hours, and then the oil and air filter are checked each time it is used.
When the machine is stored and transported, the engine must be kept level to avoid fuel and oil leakage.

Q: What work do I need to prepare before use?

A: Prepare enough fuel according to the sailing distance;
Bring a life jacket and paddle;
Bring random tools and necessary accessories;
Check the installation of the outboard motor and the transom.





Note: 
Please read the following tips before purchasing.
1. If you are a Russian customer, we will send you the package via EMS. (Including customs clearance and taxes). The time is about 30 days. (If your address is in a remote area, it will take about 55 days)
2. If you are a customer in an EU country, this method "customized by seller" is about 60 days by rail and UPS. (Including customs clearance and tax)

1. If your address belongs to a remote area, you need to pay an additional US$40.00 or contact us to choose another shipping method.
2. Please pay taxes and pick up the package after the package arrives at the local customs. We are not responsible for any customs duties and import taxes.
3. Our working hours: 9: 00-18: 30 Beijing time. In the meantime, we will respond to your message promptly. During the break, we may not be able to reply to your message, please understand. We will reply you within 24 hours.