EIBOS PTC Heater 3D Printing Filament Dryer Box 110V-220V 100W Real-time Humidity Monit Large Homothermic Filaments Storage Box Item NO.: 3256804440943827

EIBOS Extra Large Dry Box, Filament Dryer, Compatible with 1.75mm, 2.85mm, 3.00mm 3D Filament: DRY FAST, EXTRA LARGE, HIGH TEMPERATURE

1.Extra Large Homothermic Box

CYCLOPES has a large inside space, Can use 4 rolls of 0.5kg filaments/2 rolls of 1kg filaments/1 roll of 3kg filament at the same time, Suitable for multiformat filaments which including 1.75mm/2.85mm/3mm

2. Excellent drying effect

In the filament dryer, we use a 100W PTC heater to heat up space which is rare and inimitable in the market. As we know, most of the filament dryers are using a 48W PI heating pad to heat up space that cannot dry evenly. However, the same problem won’t occur in Cyclopes because of our PTC heater technology. PTC heater is also known as durable, energy-saver, and environmentally friendly.

3.Adjustable heating temperature

The drying temperature can be set and the operation process is simple. The temperature can be set in a wider range, up to 70°C.

4.Optimized heating method

Hot air heating makes drying more efficient; the unique air duct design makes CYCLOPES conform to the principle of air thermodynamics, and the filament is heated more evenly.

5.Real-time humidity monitoring

Independent humidity detector，digital display. The measuring range is from 10%to 99%. At the time when CYCLOPES is working, the humidity inside the box can drop to as low as 10%(Under ideal conditions in the laboratory).

Product Description

-WHY WE NEED CYCLOPES

When plastic is melted with moisture inside, the water molecules turn to steam and create popping noises, and visible gaps or bubbles during the printing process.

Fig.1 3D printing filament absorbs moisture in the air, and the content of internal water molecules increases;

Fig.2 After heating, the connection between water molecules and polymer chains are broken, the internal water molecules will move to the surface of the filaments:

Fig.3 The hot air can heat the 3D printing filament more uniformly and accelerate the evaporation of water molecules;

Fig.4 After drying, the water molecule content of the 3D printing filament is significantly reduced, and ready for the best printing experience.

Features

1.Extra Large Homothermic Box

CYCLOPES has a large inside space, Can use 4 rolls of 0.5kg filaments/2 rolls of 1kg filaments/1 roll of 3kg filament at the same time, Suitable for multiformat filaments which including 1.75mm/2.85mm/3mm

2. Adjustable heating temperature

The drying temperature can be set and the operation process is simple. The temperature can be set in a wider range, up to 70°C.

3.Optimized heating method

Hot air heating makes drying more efficient; the unique air duct design makes CYCLOPES conform to the principle of air thermodynamics, and the filament is heated more evenly.

4.Closed-loop constant heating

Real-time monitoring of the temperature in the box, keeping the temperature in the box constant by using the closed-loop intermittent heating mode

5.Heating time can be set freely

The heating time can be set based on your requirement，the countdown setup is from Oh to 24 hours and the shutdown is accurate to minute. You can set unlimited heating as well. In this setting，CYCLOPES is in the normally open state.

6.Fire retardant material

The core components of CYCLOPES are made of VO flame retardant materials. Built-in temperature protection switch is also included，automatic tripping over temperature. This will make CYCLOPES even safer.

7.Real-time humidity monitoring

Independent humidity detector，digital display. The measuring range is from 10%to 99%. At the time when CYCLOPES is working, the humidity inside the box can drop to as low as 10%.

8.Memory setting parameters

The parameters set last time can be automatically memorized，and will not be affected by power failure

9. Unique appearance design

CYCLOPES is designed with a sense of technology, using the visible top cover and a matte black base to let the user is able to clearly understand the current remaining material status.

10. 8 Bearings sets filament rack

CYCLOPS uses 8 bearings to carry filaments, the movement of the filaments is smoother and the printing is steady.

11. Drying & printing same time.

CYCLOPES is able to achieve drying while printing. A total of 8 holes are set on the shell to make multi-directional outlets possible which in order to satisfy the use of various types of printer or multiple printers use at the same time.

12. Product safety Certificates

CYCLOPES have CE, FCC ROHS、REACH Certificates.

Product Specifications
:

Input Voltage: AC 110V/220V 50/60Hz

Rated Power: 100W

Temperature Control Range: ≤70℃

Product Size: 213x280x305mm

Net Weight: 1.4kg Package

Size: 245x305x355mm

Total Weight: 2.0kg

Timing Length: 1min-24h or unlimited

Precision of Temperature Control: ±2℃

Maximum Capacity:

Double Reels 217x80mm

Single Reel p217x174mm

Filament Diameter: 1.75mm(need to change the Teflon Tube for 2.85mm filament)

Package Included:

1*Dryer CYCLOPES(not included the Button battery of humidity sensor)